Calibrating Bay Data...

PRECISION WORKSHOP CATALOG

Auto Repair Services

Transparent pricing, dealership-level diagnostic equipment, and certified master craftsmanship.

45 Minutes

$120

OEM Computer Engine Diagnostics

Dealership-level computerized diagnostics scanning over 1,500 CAN-Bus parameters with photographic DVI report and transparent pricing.

Key Procedure Gates:

Stage 1: Full ECU, TCU, ABS, and BCM module fault extraction with freeze-frame telemetry capture.
Stage 2: Real-time 4-channel oscilloscope analysis of primary ignition waveforms, fuel injector duty cycles, and O2 sensors.
Stage 3: High-amperage computerized battery conductance, alternator diode ripple, and starter draw analysis.

90 Minutes

$280

Performance Brake Overhaul & Resurfacing

Sub-millimeter rotor resurfacing, ceramic pads, and DOT fluid flush with 24-Month nationwide warranty.

Key Procedure Gates:

Stage 1: Micrometer runout measurement of existing brake discs against OEM minimum thickness tolerances.
Stage 2: Precision on-vehicle dual-spindle lathe resurfacing eliminating lateral disc runout down to 0.005mm.
Stage 3: Installation of low-dust ceramic brake pads with high-temp anti-rattle abutment clips and guide pin boots.

60 Minutes

$240

Dynamic Transmission Flush & Shift Relearn

Closed-loop synthetic ATF/DSG exchange, pan filter replacement, and electronic TCM relearn.

Key Procedure Gates:

Stage 1: Closed-loop hydraulic fluid exchange displacing 100% of thermally degraded fluid from torque converter and cooler.
Stage 2: Transmission pan removal, particulate cleanup of interior magnetic traps, and OEM filter replacement.
Stage 3: Refill with manufacturer-certified synthetic fluid (Dexron VI, Mercon LV, ZF Lifeguard 8/9, Dual-Clutch DSG).

40 Minutes

$110

3D Laser Wheel Alignment & Steering Calibration

Sub-millimeter optical camera alignment and digital steering angle reset for maximum grip and tire protection.

Key Procedure Gates:

Stage 1: Mounting 4-wheel high-definition optical targets without rim contact to preserve wheel finish.
Stage 2: 3D geometry camera sweep measuring thrust angle, individual toe, camber, and caster angles.
Stage 3: Sub-millimeter tie-rod and subframe eccentric bolt adjustments to factory OEM specifications.

2.5 Hours

$350

Walnut Blasting Intake Valve Decarbonization

Restore lost horsepower and smooth idle with pressurized walnut media intake valve cleaning.

Key Procedure Gates:

Stage 1: Intake manifold removal and 4K borescope photo inspection of all intake ports.
Stage 2: Manual crankshaft rotation to verify complete valve closure for each cylinder before blasting.
Stage 3: High-pressure crushed walnut shell blasting restoring valves to factory mirror-finish metal.

60 Minutes

$190

Turbocharger Boost Leak & Actuator Inspection

Smoke boost leak testing, shaft play inspection, and electronic wastegate calibration for turbocharged engines.

Key Procedure Gates:

Stage 1: Pressurized EVAP/Boost smoke test up to 25 PSI identifying micro-cracks in charge pipes and couplers.
Stage 2: Digital dial indicator measurement of turbo compressor wheel axial and radial shaft endplay.
Stage 3: Electronic wastegate voltage calibration and vacuum solenoid duty cycle testing.

3 Hours

$420

Suspension & Control Arm Overhaul

Heavy-duty bushing pressing, ball joint replacement, and ride-height torque fastening with 24-Month warranty.

Key Procedure Gates:

Stage 1: Hydraulic shaker plate inspection identifying micro-tears in fluid-filled control arm bushings.
Stage 2: 30-ton press removal of degraded rubber bushings and installation of heavy-duty OEM replacements.
Stage 3: Ball joint, tie-rod end, and stabilizer bar link replacement with pre-greased sealed units.

45 Minutes

$160

Automotive A/C Climate Evacuation & Recharge

Sub-42°F cooling guaranteed with deep vacuum leak test and gram-accurate R134a / R1234yf recharge.

Key Procedure Gates:

Stage 1: 30-minute deep vacuum decay test removing atmospheric moisture and boiling out condensation.
Stage 2: Ultraviolet dye injection and high-intensity blacklight scan of evaporator, condenser, and O-rings.
Stage 3: Digital scale weight recharge of pure refrigerant to exact manufacturer gram specification.

90 Minutes

$290

Catalytic Converter & Exhaust Diagnostic Overhaul

Infrared thermal efficiency check and oxygen sensor waveform diagnostics with 24-Month warranty.

Key Procedure Gates:

Stage 1: Thermal imaging check verifying catalyst substrate inlet vs outlet thermal temperature rise.
Stage 2: Wideband air-fuel ratio sensor response time graphing on live multi-channel oscilloscope.
Stage 3: Flex-pipe and exhaust manifold flange inspection with fresh multi-layer steel (MLS) gaskets.

2 Hours

$320

Track-Day Inspection & 4-Corner Weight Balancing

50.0% cross-weight corner balancing on digital scales and motorsport safety verification.

Key Procedure Gates:

Stage 1: Wireless 4-pad individual wheel load measurement with driver ballast in driver seat.
Stage 2: Coilover collar height adjustment achieving target 50/50 cross-weight diagonal distribution.
Stage 3: High-boiling-point (600°F+) Motul RBF / Castrol SRF brake fluid moisture test.